Skip to content

How we work

Written down before we start.

A site survey, a method statement, a documented clean and a signed certificate. Here is every step, what is in scope, what we need from you, and the commercial terms.

The protocol

Seven steps, in this order, every time.

Drawing · not to scale · the system after the seventh step
  1. 01

    Site survey & scope of work

    We walk the facility, inventory duct runs, identify access points and agree a written scope of work. CFM divided by 7 gives us duct square footage. No assumptions, no surprises on the invoice.

    You receive A written scope of work

  2. 02

    Method statement, containment & safety

    Before we start, you receive a written method statement and risk assessment covering electrical isolation, working-at-height and confined-space protocols. Plastic containment and negative pressure isolate each zone so contamination cannot escape into occupied space.

    You receive Method statement and risk assessment

  3. 03

    Pre-clean RoboCam inspection

    Our RoboCam crawler records the duct interior on photos and SD-card video, establishing a clear before-state you can see.

    You receive Before photos and SD-card video

  4. 04

    Mechanical cleaning: NPM, rotary brush & Air Whip

    A Negative Pressure Machine on one end, a rotating brush or high-pressure Air Whip on the other. The brush loosens; the NPM captures. Eco-friendly, non-corrosive, metal-safe degreasers are used where grease is present, and we guarantee they will not weaken your ducting.

    You receive Deposits captured, not spread

  5. 05

    AHU, coils, grilles & kitchen hood cleaning

    Blowers, coils, drain pans, dampers, diffusers and grilles are washed or contact-vacuumed. For commercial kitchens, hoods and filters are degreased to bare metal where access allows.

    You receive Every reachable component cleaned

  6. 06

    Access ports & microbial sanitisation

    We cut and make clean access ports wherever the duct lacks them (you provide 24-gauge GI sheet for re-fixing). Where required, a food-safe antimicrobial fog is drawn through the system to eliminate residual mould and bacteria.

    You receive Access ports and a treated system

  7. 07

    Post-clean RoboCam, photo report & Job Completion Certificate

    A second RoboCam pass documents the after-state. You receive the before/after photo and video report, a cleanliness verification and a signed Job Completion Certificate for your records and your auditors.

    You receive Photo and video report, signed certificate

Scope

What a kitchen exhaust clean covers.

CFM ÷ 7 = duct area in square feet. We use this as our starting point, then verify on site.

Included Add-on

Included

Add-ons, quoted separately

  • Deep cleans requiring full kitchen shutdown
  • Work outside of agreed operating hours
  • Coil-only cleaning as a standalone scope
Quote this scope

Typical unit rate for commercial kitchen exhaust cleaning starts at ₹9/sqft. Final rate depends on access, grease load and operating hours.

Size it

Estimate your kitchen exhaust clean.

It is on the fan nameplate or the air balancing report.

Don't know your CFM? Send us a photo of the fan nameplate.

CFM ÷ 7 = duct area in square feet. We use this as our starting point, then verify on site.

Enter your airflow to see the duct area and a starting estimate.

Typical unit rate for commercial kitchen exhaust cleaning starts at ₹9/sqft. Final rate depends on access, grease load and operating hours.

Plus GST. The vertical riser and fan unit, and UV or air-washer units, are add-ons quoted separately.

Kitchen inspection frequency

How often should the exhaust be inspected?

Type of cooking

Minimum inspection interval

Every 6 months

NFPA 96 term: Semiannually

These are minimum inspection intervals for the exhaust system. Your authority having jurisdiction, insurer or the grease found on inspection can require cleaning sooner.

Source: NFPA 96 (2024), Table 12.4

From you

What we need on site.

  • Power & water supply

    Standard site power and a water point within reasonable reach of the work zone.

  • Engineering team access

    Your engineering staff on call to remove and replace fans, dampers, VAVs and grilles where needed.

  • Isolation & tag-out

    All fans to be turned off, isolated and tagged out before cleaning begins, for crew safety.

  • Waste disposal point

    A designated collection point for grease, rags, plastic and debris removed during cleaning.

  • Scaffolding or hydraulic ladder

    Provided by you where grilles or high-level components require working at height.

  • 24-gauge GI sheet

    Supplied by you to re-fix the access ports we cut into your ducts.

Food and accommodation for on-site crew is arranged by the client for sites outside Mumbai.

Commercial terms

Terms, plainly stated.

  • Chemical-safety guarantee
  • Photo + video evidence
  • Job Completion Certificate
  • Payment terms

    50% advance with the work order. Balance within 3 working days of submission of invoice, Job Completion Certificate and photo/video report.

  • Proforma & tax invoice

    Proforma issued on completion. Tax invoice issued on receipt of final payment. GST 27AFZPT8549P1ZS · SAC 998717.

  • Exclusions

    Governing-body approvals and anything not specifically quoted for are excluded. Any variation is priced separately and flagged in writing before work resumes.

  • Cancellation

    Items removed within 7 days of signing incur a 25% charge. After 7 days, removed items are charged at 100%.

Quotations are typically valid for 30 days from issue date.

Questions

Every answer, in one place.

Book a free duct inspection.

Tell us the building and the ducts. We reply with a written scope and a quote.

Mon – Sat · 09:30 – 19:00 · Emergency & night-shift cleans on request